Toggle Latch
90703S Adjustable Draw Latch for Doors That Do Not Line Up
Most latch failures on toolboxes, cabinets, and equipment doors come from one cause: the door and frame gap changes after assembly, painting, or gasket compression. A fixed latch either will not close or leaves the door loose. The 90703S adjustable draw latch solves this by letting you set the tension after the door is hung.
We make the 90703S in stainless steel, with a steel version available on request. The latch compresses the door for a firm seal and accepts a padlock through the locking hole. We supply it to ship outfitters, refrigeration equipment builders, medical equipment manufacturers, and agricultural and RV assemblers.
How the Adjustment Works
The latch body has an adjustable draw length. Before final tightening, you set the hook position so the latch pulls the door against its gasket without over-compressing it. This is the step that fixed latches cannot offer, and it is why the 90703S suits doors with tolerance stack-up from multiple parts.
Adjustment is made at installation, not in service. Once set, the latch holds its position through normal open and close cycles.
What to Check Before You Set the Tension
- Door and frame gap at the latch point, measured after gasket installation
- Hook style and mounting position on the frame side
- Whether a padlock will be used, and the shackle diameter
- Door material and screw or rivet type for the mounting surface
90703S Specifications
| Item Number | 90703S |
|---|---|
| Type | Adjustable draw latch / toggle latch |
| Standard Material | Stainless steel |
| Alternative Material | Steel version available on request |
| Closing Action | Over-center toggle with adjustable draw length |
| Locking | Compressed and pad-lockable through locking hole |
| Hook Options | Various hooks available on request |
| Compliance | Meets European standard |
| Customization | OEM/ODM accepted, other finishes and designs available |
Send us your door gap measurement and hook mounting position. We will confirm the adjustment range and recommend the hook style for your frame.
Stainless Steel or Steel: Which Version Fits Your Product
| Consideration | Stainless Steel (Standard) | Steel Version (On Request) |
|---|---|---|
| Corrosion resistance | Suitable for humid, outdoor, and wash-down areas | Requires plated finish for moisture exposure |
| Typical environment | Ships, refrigeration, medical equipment, RV exteriors | Indoor cabinets, toolboxes, dry storage |
| Finish options | Mill finish standard, other finishes on request | Plated or coated finish |
| Relative cost | Higher material cost | Lower material cost at volume |
| Best for | Applications where rust stains or replacement are costly | Cost-controlled indoor products with stable humidity |
Hook and Accessory Options
The latch body is only half of the assembly. The hook determines how the latch engages the frame, and the wrong hook is a common cause of poor compression.
- Standard hook: for flat frame surfaces with a straight pull
- Extended hook: for frames set back from the door face
- Angled hook: for frames where the pull direction is not perpendicular
We supply various hooks on request. Send your frame drawing or a photo of the mounting area, and we will match the hook to your geometry.
Applications We Supply This Latch For
- Ship and marine storage cabinets and locker doors
- Refrigeration and cold storage equipment panels
- Medical equipment enclosures and carts
- Agricultural equipment access panels
- Recreation vehicle exterior storage compartments
- Toolboxes, storage cases, and general cabinets
Each of these applications has a different tolerance and corrosion requirement. Tell us the environment and door material, and we will confirm whether the stainless steel standard version or the steel version is the better fit.
Ordering and Sample Information
We accept OEM and ODM orders for the 90703S. Minimum order quantity is 500 pieces. Samples are free of charge; provide your DHL, TNT, or FedEx account number and we will have samples ready within 3 days.
For volume orders, we can discuss other finishes, other designs, and hook customization. Send your requirement with quantity and destination country.
Request 90703S Sample & Adjustment RangeRelated Pages
Frequently Asked Questions
The adjustment range depends on the hook selected and the mounting position. Send us your door gap measurement and we will confirm the usable range for your frame before you order.
Yes, the 90703S is compressed and pad-lockable through the locking hole. Shackle diameter depends on your padlock choice. Tell us the padlock you plan to use and we will confirm compatibility.
Choose steel when the product stays indoors with stable humidity and cost control matters more than corrosion resistance. Choose stainless steel when the latch sees moisture, wash-down, or outdoor exposure, or when rust stains would damage the product's appearance.
Minimum order quantity is 500 pieces. Samples are free of charge. Provide your courier account number and samples will be ready within 3 days.
Hot Tags: Toggle Latch, China, manufacturers, suppliers, factory, customized, general, Gerenal non locking version, adjustable draw latches, non locking hole latch, Gerenal Compressed and pad lockable , non locking version, Gerenal non locking hole latch
Previous
No InformationYou Might Also Like
Send Inquiry